Skip to content
NH3 Detector
Low voltage 12-24 Vac/Vdc Monitor
Three separate relays for three alarm levels
LED Display shows Active Gas Concentration
Available in PPM Alarm Options
Technician Adjustable Settings & Options
Built-in buzzer
Made in USA
Linear Heat Detector Cables.
Resettable linear heat detector cable – for solar applications.
To be used with Linear Heat Detector Control Unit & EOL.
Can be used in areas that require regular Heat sensing & Detection System.
Cables can be reset once normal temperature is realized – Equipment safety.
Can be used to measure temperature in critical equipment.
System can be used to switch on passive cooling / fans to prevent overheating.
Cable Don’t Need to be Replaced After Detection – Cables will normalize. Contact us for more information.
Aspirating Gas Detector – Sampling Type Detection.
Aspirating Gas Detection System – Integrated Control.
Detect toxic and flammable gases by air sampling.
Flammable Gas, Toxic Gas & Oxygen Level Monitoring.
Gas detectors are available with gas pump for air sample.
Special gas pumps are chemical resistant for toxic gases.
Explosion proof (ATEX) pumps are used for flammable gases.
Pumps are made from chemically resistant material and design.
Air flow, vacuum pumps & sensor to be used as per requirement.
HVAC Ducts requires specialized venturi effect aspirating units.
Gas Detectors for HVAC Ducts require specialized kits as required.
Contact us for more information on aspirating gas detectors.
Specialty Mixed Calibration Gas
Included Regulator & PVC Hose
Additional Accessories / Calibration Equipment
Included Analytical Certificate with Calibration Cylinder.
Regulator 0.5L/min or 1L/min – Brass for Flammable Gas & SS for H2S.
Different Gas Mix Available – Flammable, Oxygen & Toxic.
Contact us for more information.
Carbondioxide (CO2) Fixed Gas Detector.
Low voltage 12-24 Vac/Vdc Monitor.
Three separate relays for three alarm levels.
LED Display shows Active Gas Concentration.
Available in PPM and %VOL Alarm Options.
Technician Adjustable Settings & Options.
Built-in buzzer – For Alarm Signaling & Alert.
Contact us for more information.
Carbon monoxide CO Gas Detector.
For use in kitchens & indoors – Safe Area Installation.
Local Alarm Buzzer & Relay Output – Alarm & Trouble.
LED Status Indicator – Red, Amber & Green LED’s.
Integrate directly into the Fire Alarm System.
QCD Approved – For use with Fire Alarm Panel.
Contact us for more information.
Crowcon IRmax Infrared Flammable Fixed Gas Detector
Wall Mounting & Pipe Mounting with Suitable Accessories.
4-20mA Analog Output for Integration with Control System.
Optional – HART & RS-485 MODBUS for Addressable System.
SIL 2 Rated for Process & Functional Safety Equipment’s.
ATEX Certified for use in Explosive Atmospheres & Offshore.
Enclosure: Stainless Steel 316 c/w Optional Display.
Contact us for more information.
Crowcon TXgard-IS+ Toxic & Oxygen Gas Detector.
Intrinsically Safe Fixed Gas Detector (with Isolator)
Local LCD Display – Clear Display with menu options.
Used to detect Toxic Gases & Oxygen Levels.
Explosion Proof (ATEX) Certified for Zone 0 areas.
Capable of Detecting H2S, NH3, O2 & Toxic Gases.
4-20mA Signal – For Analog Signal to PLC or BMS.
Calibration to be performed manually on field.
Can be used as sampling detector with flow adaptor.
Strong, sturdy carbon loaded nylon enclosure with IP65.
Contact us for more information.
Xgard Bright – Flammable, toxic gas & oxygen monitoring.
Available in ADC12 Aluminium Alloy Enclosure Material.
IP65 Protection for use in Outdoors (Optional IP66)
Addressable Gas Detector for large area networks.
Clear OLED Display for use in sunlit / bright areas.
Magnetic non-intrusive calibration with key.
ATEX Certified for use in hazardous areas.
Built in Relays – Alarm 1, Alarm 2 & Fault.
Certified for use in Zone 1 & Zone 2 Areas.
Contact us for more information.
Crowcon Xgard Fixed Gas Detector
Xgard Type 1 – Nylon: 0.5kg / Alloy: 1kg / 316 SS: 3.1kg
Xgard Type 2 – Aluminium: 1kg / Stainless steel: 3.1kg
Xgard Type 3 – Aluminium: 1kg / Stainless steel: 3.1kg
Xgard Type 4 – Aluminium: 1.5kg
Xgard Type 5 – Aluminium: 1kg / Stainless steel: 3.1kg
Xgard Type 6 – Aluminium: 1kg / Stainless steel: 3.1kg
Explosion Proof – ATEX Certified Fixed Gas Detector
Low-cost reliable Gas Detector – In Battery Rooms.
Available in Nylon GRP, Aluminium or SS 316.
Ability to detect several ranges of flammable gases, toxic & oxygen.
4-20mA Analog Signals – Direct PLC & Plant Integration.
Requires half-yearly calibration and system testing.
QatarEnergy Approved for use in Gas Detection System.
Contact us for more information.
Crowcon Xgard Type 1 Fixed Gas Detectors.
Fixed Point Ex ia Intrinsically Safe Toxic & Oxygen Detectors.
Uses an electrochemical sensor to provide 2-wire 4/20mA Output.
Operating temperature between -40°C to +50°C & humid spaces.
Xgard Type 1 has standard GRP Enclosure – Glass Reinforced Nylon.
GRP Polymers are chemically resistant & cost effective for wide use.
Optional Accessories include spray deflector, flow adaptor & W/P caps.
Comes with M20 (standard), 1/2″ NPT or 3/4″ NPT cable gland optional.
Offering Calibration, Sensor & Component Spares, Replacement.
Contact us for more information.
Crowcon Xgard Type 2 Flameproof Fixed Gas Detectors.
Type 2 Exd Flameproof Toxic & Oxygen Detectors.
Uses an electrochemical / pellistor sensor for gas detection.
Operating temperature between -40°C to +50°C & humid spaces.
Xgard Type 2 has standard Aluminium Enclosure – Rigid & Strong.
Aluminium enclosures are highly durable with tough polyester coat.
Accessories available for duct mounting & sampling applications.
Optional Accessories include spray deflector, flow adaptor & W/P caps.
Comes with M20 (standard), 1/2″ NPT or 3/4″ NPT cable gland optional.
Offering Calibration, Sensor & Component Spares, Replacement.
Contact us for more information.
Crowcon Xgard Type 3 Fixed Gas Detectors.
Exde Flameproof Flammable Explosion Proof Gas Detectors.
Uses poison resistant 3-wire pellistor sensor for flammable gas.
Operating temperature -40 to +80°C & humid conditions installation.
Optional Accessory Enclosure required for connection – For easy zero/cal.
Aluminium Enclosure with Polymer coating as standard – ATEX Certified.
Optional Accessories include spray deflector, flow adaptor & W/P caps.
Comes with M20 (standard), 1/2″ NPT or 3/4″ NPT cable gland optional.
Offering Calibration, Sensor & Component Spares, Replacement.
Contact us for more information.
Crowcon Xgard Type 4 High Temperature Flammable Gas Detectors.
Exd Flameproof Flammable Gas Detectors use poison resistant sensors.
Detector comes in either 316 Stainless Steel or Aluminium Housing.
Contains terminals for 3-wire mV Wheatstone Bridge Output.
Operating Temperature of -20°C to 150°C for a wide operating range.
Optional Accessory Enclosure required for connection – For easy zero/cal.
Aluminium Enclosure with Polymer coating as standard – ATEX Certified.
Optional Accessories include spray deflector, flow adaptor & W/P caps.
Comes with M20 (standard), 1/2″ NPT or 3/4″ NPT cable gland optional.
Offering Calibration, Sensor & Component Spares, Replacement.
Contact us for more information.
Crowcon Xgard Type 5 Flammable Gas Detector.
Consists of poison resistant pellistor sensor for flammable gases.
Built-in amplifier unit to provide 3-wire 4-20mA Analog Output.
Operating temperature between -40°C to +55°C wide temperatures.
Aluminium Enclosure with Polymer coating as standard – ATEX Certified.
Optional Accessories include spray deflector, flow adaptor & W/P caps.
Comes with M20 (standard), 1/2″ NPT or 3/4″ NPT cable gland optional.
Offering Calibration, Sensor & Component Spares, Replacement.
Contact us for more information.
Crowcon Xgard Type 6 Fixed Gas Detectors.
Type 6 is designed to Detect % VOL Levels of Flammable Gases. Uses thermal conductivity sensor within metallic enclosure (ATEX).
Operating temperature +10°C to +55°C & humid conditions installation.
Aluminium Enclosure with Polymer coating as standard – ATEX Certified.
Optional Accessories include spray deflector, flow adaptor & W/P caps.
Comes with M20 (standard), 1/2″ NPT or 3/4″ NPT cable gland optional.
Offering Calibration, Sensor & Component Spares, Replacement.
Contact us for more information.
Crowcon Xgard Fixed Gas Detector
Xgard Type 1 – Nylon: 0.5kg / Alloy: 1kg / 316 SS: 3.1kg
Xgard Type 2 – Aluminium: 1kg / Stainless steel: 3.1kg
Xgard Type 3 – Aluminium: 1kg / Stainless steel: 3.1kg
Xgard Type 4 – Aluminium: 1.5kg
Xgard Type 5 – Aluminium: 1kg / Stainless steel: 3.1kg
Xgard Type 6 – Aluminium: 1kg / Stainless steel: 3.1kg
XgardIQ – Stainless steel 316: 5.5kg
TXgard-IS+ – Carbon Loaded Nylon Enclosure: 0.7kg
Flamgard Plus – Marine Grade Alloy / SS 316: 2.2kg
TXgard Plus – Marine Grade Alloy / SS 316: 2.2kg
Explosion Proof – ATEX Certified Fixed Gas Detector
Low-cost reliable Gas Detector – In Battery Rooms.
Available in Nylon GRP, Aluminium, Marine Alloy or SS 316.
Ability to detect several ranges of flammable gases, toxic & oxygen.
4-20mA Analog Signals – Direct PLC & Plant Integration.
Requires half-yearly calibration and system testing.
Contact us for more information.
FGard IR3 Flame Detector
Detect all Hydrocarbon Fires within 60m.
Heated windows to prevent condensation.
Smart System – Doesn’t Require Testing
SIL 2 Approved
FM Approved
ATEX Approved for use in Hazardous Areas
Enclosure: Copper free Aluminium or SS
Output: 4-20mA, Alarm & Fault Relays
HART Capable
Optional : Pole Mount Kit, Sunshield, Mounting Bracket, Flame Simulator Test Kit
Flamgard Plus – Flammable Gas Detector.
For Hydrocarbon, Hydrogen, Petrol & Vapor Detection.
Non-Intrusive Calibration – No hot work permits required.
Added Fault & Alarm Relays.
IP65 Protection for use in outdoors.
Contact us for more information.
Safe Area Gas Detector.
Gas Detector available with Gas Panel / Controller.
Calibrated to detect LPG, CO, Toxic & Flammable Gas.
Flame Detectors available for Zone 2 Areas with QCD.
To be used in non-hazardous areas.
Basic Ingress Protection from Sun, Water & Dust.
Half yearly calibration & maintenance.
Contact us for more information.
Crowcon Air Aspirated Sample Systems/ Gas Sampling System.
Only Sampling System usable in Hazardous Area based on installation.
Uses eductor for sampling (using Venturi Effect) – The eductor is driven by compressed air to create a negative pressure to draw the sample.
Electrical Components are the sensor and Intrinsically Safe flow device.
Principle: The air aspirated system uses a compressed air driven vacuum generator to draw a gas sample from a single point. Explosion proof gas detectors are fitted to monitor for flammable gases & toxic gases.
Flow rate is limited to 1m/sec – Can be adjusted as per request & approved design with factory approvals.
Certified for use in Zone 1 or Zone 2 hazardous areas, IP-65 Rated.
Customized Engineered Solutions & Support from Factory for Design.
Contact us for more information.
GECA Fixed Gas Detector – For LPG & Flammable Gases / Fumes
Approved for Installation in LPG Gas Piped Areas
Commercial Gas Detector with Controls & Indicators
Contact us for more information.
Greystone CERMC – Indoor Carbon Dioxide Transmitter
NDIR Sensor for Long Life CO2 Readings
4-20mA Analog Output, MODBUS Outputs & Relay Outputs
Optional Temperature Sensor
Contact us for more information.
Greystone CMD5B1000 & Other – CO Detector
0-300ppm CO Range – For use in Carparks
Analog 4-20mA Output or MODBUS
AC or DC Power Options.
Inbuilt relay for low powered device activation.
Easy and quick calibration.
Contact us for more information.
Greystone CMD5B5 Series – Duct Carbon Monoxide Detector
Analog 4-20mA Output or BACnet & MODBUS Output
AC or DC Power Options
Range from 0-500 ppm (Ranges field adjustable)
Built in LCD for operation and use.
Front Panel Test Switch, Status Indicator & Buzzer
Replaceable Sensor
One / Two Alarm Relays & RS-485 Network Configuration.
Contact us for more information.
Hydrogen Fixed Gas Detector
Low voltage 12-24 Vac/Vdc Gas Detector
Two separate relays for two alarm levels
LED Display shows Active Gas Concentration
Can be configured and calibrated to Hydrogen, Methane & Propane
Available in %LEL Alarm Options
Technician Adjustable Settings & Options
Contact us for more information.
H2S – Fixed Toxic Gas Detector.
Low voltage 12-24 Vac/Vdc Monitor.
Three separate relays for three alarm levels.
LED Display shows Active Gas Concentration.
Available in PPM Alarm Options & Signals.
Technician Adjustable Settings & Options.
Built-in buzzer & Sounder Relays.
Contact us for more information.
IGD TOCSIN 102 – Fixed Gas Detector.
Available for flammable & toxic gas detection.
Explosion Proof Certified for Hazardous Areas.
IP66 Ingress Protection for outdoor installation.
Enclosure: SS 316 with Flameproof Protection.
Calibrated to detector LPG 0-100% LEL.
Support for other hydrocarbon gas detection.
Contact us for more information.
Sale!
Fixed LPG Gas Detector.
Low-cost Combustible Gas Detector.
For use in Kitchens & Indoors.
Green & Red LED Status Indicators.
Optional GD-2A Available with Local Buzzer.
Can be Directly Integrated to Fire Panel (FACP).
QCD Approved – For use with Fire Alarm System.
Contact us for more information.
H2/LPG/CH4 Fixed Gas Detector.
Low voltage 12-24 Vac/Vdc Monitor.
Three separate relays for two alarm levels.
LED Display shows Active Gas Concentration.
Can be configured and calibrated to Hydrogen, Methane & Propane.
Available in %LEL Alarm Options & Built-in Buzzer.
Technician Adjustable Settings & Options.
Contact us for more information.
Methane Fixed Gas Detector.
Low voltage 12-24 Vac/Vdc Gas Detector.
Two separate relays for two alarm levels.
LED Display shows Active Gas Concentration.
Can be configured and calibrated to Hydrogen, Methane & Propane.
Available in %LEL Alarm Options & Built-in Buzzer.
Technician Adjustable Settings & Options.
Contact us for more information.
Oxygen Gas Detector with Default 20.9% VOL Calibrated.
4-20mA Analog Signal Enables to check Deficiency & Enrichment.
Red LED Display with Green Power Status Indicator.
Field Configurable Relay Outputs with Custom Values.
Available in White or Grey Housing – For all designs.
Easy to Replace Sensor & Maintenance.
Built-in buzzer – For Alarm Signaling & Activation.
Contact us for more information.
Open Path IR Flame Detector.
Range up-to 200m for detection.
Explosion Proof – ATEX Certified.
Heated windows to prevent condensation.
SIL 2 Approved for functionality.
FM Approved for use with Fire Alarm.
QCD Approved.
Contact us for more information.
Crowcon Environmental Sampling Unit / Sampling Gas Detector.
Low-cost Air Sampling Unit for HVAC & other critical Equipment.
Detection of toxic / flammable gases in hot, humid or dusty environments.
Single Point / Multi Point / Sequential / Aspirated Sample System.
Low & High Alarms signals to program Relays for Shutdown / AV Units.
Single Point – Gas Detector using Pellistor / IR Sensor for High Temps.
Multi Point – Made of Multiple Point for Environmental Gas Monitoring.
Engineered / Customized Solutions available certified for Hazardous Areas (with 1, 2 or 3 sensors) and Non-Hazardous Areas. Can be programmed for executive action based on detection from multiple detectors.
Contact us for more information.
Smart 3-R Gas Detector – For Flammable, Toxic & Oxygen Detection
Smart 3-R Lite Gas Detector – Refrigerant Detection
Multi-Colour LED Ring provides aesthetic visual indication.
Available with a variety of gas sensors & detection.
4-20mA Analog Signal – Integration with Gas Panel / PLC.
Contact us for more information.
SMART 3G-C2 Fixed Gas Detector
Capable of detecting more than 50 types of Gases.
Toxic, Flammable, Oxygen & Refrigerant Gases.
Built-in Self Diagnosis for Fault Identification.
SIL 2 Certified.
ATEX Certified for use in Explosive Areas.
IP 65 Rated with Aluminium Enclosure.
Contact us for more information.
SMART 3G-D2 Fixed Gas Detector.
Can be used for flammable, toxic & refrigerant gases.
SIL 2 Certified & ATEX Certified for use in Explosion Proof Areas.
Non-intrusive Calibration using Magnetic keys.
Capable of SIL 3 Certification with applicable system.
Intrinsically Safe Version Available.
IP 65 Ingress Protection.
LCD Display, 5 Status LED & 4 Indicator LED.
4-20mA Analog Outputs & RS485 Addressable Output.
Green LED Ring around Display for Alarm Status Indication.
Contact us for more information.
SMART S-MS 3A Fixed Gas Detector.
Can be used for Flammable & Toxic Gases.
SIL 2 Approved.
Redundant system ensures SIL 3 Certification.
IP 65 Protection & Explosion Proof.
Enclosure: Aluminium or SS
3 Relay Outputs for AL1, AL2 & Fault.
Optional HART.
Contact us for more information.
IGD TOC-750 Addressable Gas Detector.
For Safe Area Installation Only.
Detection for over 400 Gases & Vapors.
Multiple I/O Points for Input & Output Control.
Enclosure: ABS Plastic in White Color.
Auto Swap of Sensors & Auto Changeover.
Addressable Detector with IGD Control Panel.
Contact us for more information.
TXgard Plus – Flameproof Toxic & Oxygen Gas Detector
Local LCD Display for menu & magnetic key operation.
Explosion Proof – ATEX Certified for use in Hazardous Areas.
Non-Intrusive Calibration with custom Magnetic Key.
Added Fault & Alarm Relays – For Signaling & Alarm.
IP65 Protection for use in outdoors – dust & water.
Contact us for more information.
XgardIQ – Fixed Addressable Gas Detector.
Used to detect flammable, toxic, oxygen or High Temperature H2S.
Infrared Sensors Available for Accurate Flammable Gas Detection.
IP 66 Ingress Protection – To prevent Water & Dust Ingress.
Remote Sensor Assembly Kits Available for Remote Sensor Placement.
Explosion Proof – ATEX Certified for use in Hazardous Areas.
SIL 2 Certified – For Performance & Equipment Integrity with DCS.
Local OLED Display – Clear & Bright Readings even in sunlight.
Enclosure: 316 SS – Corrosion Proof & Rust Proof in salty atmospheres.
Output: 4-20mA Signals & RS-485 MODBUS RTU – Analog & Digital.
Non-intrusive Calibration – Button Controls for quick and easy use.
Hot Swappable Sensors – Does not require Hot Work Permit.
LED Indicators for Detector Status, Fault & Power Indication.
Event logger – To measure continuous gas monitoring.
Contact us for more information.
Crowcon Xgard Fixed Gas Detector
Xsafe – 1kg
ATEX Certified Fixed Gas Detector
Low-cost reliable Gas Detector
Aluminium Enclosure.
Ability to detect several ranges of flammable gases.
Hydrogen, LPG, Methane, Ammonia & Other Organics.
4-20mA Analog Signals – PLC & Plant Integration.
Contact us for more information.
ㅤ(+974) 5584 7568 / 3384 5147 ㅤㅤ
ㅤㅤㅤㅤ ㅤㅤ 
ㅤsales@crowngasqatar.com
ㅤㅤㅤㅤㅤㅤㅤㅤㅤㅤㅤㅤㅤㅤㅤ 
ㅤ(+974) 3384 5147
